Table of Contents
- Integrated control from raw material to delivery
- In house engineering before release to fabrication
- Material traceability and material verification
- Tank fabrication and component integration
- Certified welding and manufacturing quality control
- NDE during fabrication
- Prefabricated tank components
- QA/QC for product consistency
- Industrial supply chain for turnarounds
- From shop to field
- Applying code compliance to the product
- Cost control from the fabrication stage
- Conclusions
- Sources
In an aboveground storage tank (AST) project, a deviation discovered during field installation often originates much earlier: an incomplete specification, a pending dimensional review, an incorrect material selection, an unidentified interference, or a component released without verifying all of its interfaces. When engineering, fabrication, inspection, documentation, and logistics operate as separate activities, the resulting risk is ultimately transferred to the field.
At HMT, we approach the fabrication and supply of tank components as a continuous technical process, from defining project requirements through delivery and installation. The objective is to reduce variability, limit rework, and protect construction, repair, and turnaround windows.
Integrated control from raw material to delivery
For us, controlling fabrication means maintaining technical responsibility for the variables that determine the finished product: design, materials, geometry, welding, inspection, coatings, documentation, and delivery sequence. HMT operates state-of-the-art fabrication facilities in Blackwell, Oklahoma, and Baytown, Texas, providing design, manufacturing, and engineering services for aboveground storage tanks.
Our in-house capabilities include engineering, design, detailing, structural analysis, and calculations, as well as laser cutting, CNC plasma cutting, waterjet cutting, machining, beveling, plate and pipe rolling, welding, blast priming, and finish coatings. Integrating these disciplines reduces the technical interfaces that typically arise when design, fabrication, and inspection are distributed among different organizations.
The value extends beyond having production equipment available. The real advantage is the ability to transfer an engineering decision into fabrication while maintaining its dimensional, metallurgical, and functional requirements, and to return a deviation to the technical team before it becomes a field modification.
A component is not complete simply because it has passed through the final shop operation. It must be dimensionally compliant, inspected against applicable requirements, properly identified and documented, and prepared to integrate into the planned installation sequence.
In house engineering before release to fabrication
Quality begins before the first cut. Material, thickness, geometry, loads, tolerances, welds, interfaces, accessibility, and installation method must be resolved before drawings are released for production. For work involving existing assets, actual tank condition may be more important than nominal geometry.
Out-of-roundness, verticality deviations, settlement, rim spaces, nozzle locations, columns, and other interferences can affect the fit and operation of floating roofs, seals, roof drain systems, platforms, and appurtenances. Fabricating solely from historical information without validating these variables introduces uncertainty where the opportunity for correction during a turnaround may be limited. HMT Engineering provides specification reviews, fabrication and as-built drawings, tank design calculations, structural analysis, and other technical services for both new and existing tanks.
Design for fabrication and installation
Our approach is to review a component from three perspectives before production: what it must comply with, how it can be fabricated, and how it will be installed. This review helps define which characteristics must be verified during fabrication and which can be inspected after the assembly has been completed.
Revision control is equally important. An approved change must flow into drawings, bills of material, cutting programs, fabrication instructions, and related documentation. A component fabricated perfectly to an obsolete revision is still the wrong component for the project.

Material traceability and material verification
Material traceability establishes the relationship between a finished component and the documentation demonstrating which material was used. Depending on contractual requirements, this may include specification, grade, thickness, heat or lot number, material certificates or Mill Test Reports (MTRs), and additional project-specific verification.
When plate, structural shapes, or pipe are subdivided during cutting or machining, identification must be maintained using the method established for the work. Losing that relationship complicates document release and may unnecessarily expand the scope of an investigation when a deviation is identified.
HMT provides Positive Material Identification (PMI) capabilities along with Mechanical Testing (HMT’s) and metallurgical testing services. mechanical testing laboratory performs Tension (Tensile) Testing, Bend Testing, hardness testing, Impact (Charpy) Testing, and Elemental Analysis by Optical Emission Spectroscopy (OES) for material characterization.
Verification should be selected according to risk and specification requirements. PMI, OES, mechanical testing, and metallurgical examination are not interchangeable; each method addresses a different question regarding material identity, chemical composition, mechanical properties, or material condition.
Tank fabrication and component integration
HMT’s tank fabrication capabilities cover structural, operational, and auxiliary components that ultimately must function together within the same asset. HMT’s list of fabricated items includes shop-primed shell plate, shop-built pontoons, floating suctions, roof drain systems, shell and roof nozzles, clean out doors and assemblies, platforms, center columns, shell and roof plate, foam dams, gauge poles, wind girders, rolling ladders, manways, rafters, girders, sumps, and other tank accessories and appurtenances.
This range of components demonstrates why interface control matters. A nozzle must maintain the required elevation and orientation; a pontoon must integrate with the roof geometry; a roof drain system must travel through its intended path without interference from tank internals; and a rolling ladder must accommodate the expected floating roof travel.
HMT also integrates specialty fabrication with Tank Repair & Maintenance. Field capabilities include shell repair, bottom plate replacement, tank releveling, foundation repairs, tank jacking and repositioning, fixed and floating roof repairs or full replacements, restoration of sunken or damaged floating roofs, fittings, nozzles, manways, appurtenances, custom engineering, and specialty fabrication. That field experience provides practical feedback on how components should be designed and prepared in the shop.
Certified welding and manufacturing quality control
Welding must be treated as a controlled fabrication process compatible with the material, geometry, and intended service. At HMT’s fabrication facilities, welders are certified to Carbon Steel AWS D1.1, aluminum AWS D1.2, and stainless steel AWS D1.6.
Personnel qualification does not eliminate the need to control weld preparation, fit-up, welding sequence, distortion, and final joint condition. A discontinuity may originate at different stages of fabrication, so relying exclusively on final inspection reduces the opportunity to intervene before subsequent operations conceal the condition or make repair more complex.

NDE during fabrication
Manufactuing quality control is supported by HMT’s In-House NDE Capabilities, including Level II quality inspections, Certified Welding Inspection (CWI), radiography, Ultrasonic Testing (UT), magnetic particle testing, Positive Material Identification (PMI), Penetrant Testing (PT), and Visual Testing. Method selection should reflect the material, geometry, fabrication process, and type of discontinuity being evaluated.
NDE does not replace dimensional control. A weld can fully meet its acceptance criteria while being part of a component with an incorrect radius, orientation, or hole pattern. Weld integrity and dimensional conformity are separate controls that must converge before final release.
Prefabricated tank components
The use of prefabricated tank components transfers operations from the field into a controlled shop environment, where they are less affected by weather, access restrictions, permits, lifting equipment, available space, and coordination with other contractors. It also allows features to be inspected before installation makes corrections more difficult.
For the ALLENTECH Skin and Pontoon IFR, HMT states that components are prefabricated to the maximum extent to ensure quality and ease of installation. Perimeters are rolled to the tank radius and pre-drilled for seals; beams and clamps are pre-drilled and cut to the required length; special pontoon lengths are determined during the design stage; perimeter sheeting is cut to the IFR radius; and other components are shop-prepared before shipment.
The ALLENTECH Full Contact IFR demonstrates another level of shop-controlled preparation. Its edge closures and penetrations are seal welded to the panels, modules are pressure tested in the factory, and HMT identifies no field fabrication as one of the system’s design features. Each module is fully inspected and pressure tested using helium leak detection equipment before shipment.
These examples demonstrate an important fabrication philosophy: move as many operations and verification steps into the shop as is technically practical. The goal is for the installation team to receive components that have already been prepared, verified, and dimensionally coordinated with the system being assembled.

QA/QC for product consistency
An effective QA/QC program should prevent deviations while generating objective evidence of conformity. This requires defined responsibilities, inspection points, acceptance criteria, records, nonconformance management, and clear release conditions for the finished product.
Product consistency depends on repeatable processes: controlled documentation, qualified personnel, appropriate equipment, defined parameters, and consistent inspection methods. For the customer, consistency means that equivalent components supplied within the same project maintain the functional requirements established by Engineering.
Performance metrics may include first-pass acceptance, rework, recurrence of discontinuities, nonconformances by cause, milestone compliance, and documentation release. Their value lies in identifying where process stability begins to deteriorate so corrective action can be directed to the actual source of variability.
HMT also states that its AST products are supported by a global supply chain and lean manufacturing to deliver quality while maintaining competitive lead times. Supply consistency therefore requires coordination among material availability, production capacity, inspection, and lead time rather than allowing each activity to progress under separate priorities.
Industrial supply chain for turnarounds
During a turnaround, late delivery is an obvious problem; an incomplete delivery can have the same effect. A component that arrives without required appurtenances, identification, or documentation can stop an activity even when the main fabricated item is physically on site.
For HMT, preparation begins before mobilization. Its Turnaround Inspection Services include Supplier Surveillance and Inspection, Turnaround Planning and Scheduling, Cost Tracking and Estimating, Pre-turnaround Inspection & Assessment, Documentation Packages, Quality Management, Third-Party Inspection, and verification of compliance with client requirements.
Pre-turnaround inspection also helps establish the work scope before shutdown. Identifying a repair early provides time to complete Engineering, procure materials, and prepare components before the asset is removed from service. HMT combines advanced NDE, in-house fabrication, design capabilities, and turnaround planning to support controlled execution and reduce avoidable delays.
From shop to field
Components should be organized according to tank, system, and installation sequence. Packaging, identification, weight, handling points, preservation, and documentation are part of the technical supply scope; they are not separate activities that begin only after fabrication is complete.
On multi-tank projects, shop priorities should align with the construction schedule. Producing the easiest component first may improve an internal production metric while leaving the activity controlling the critical path without the materials required to proceed.
Applying code compliance to the product
Compliance involves more than placing a standard designation on a drawing. Applicable requirements must be converted into specific decisions regarding design, materials, fabrication, welding, inspection, testing, and documentation.
HMT performs work associated with API 650, API 620, and API 653, while its New Tank Construction capabilities also include AWWA D100, depending on the application. API confirms that API Standard 650, 14th Edition, was issued in August 2025; therefore, the contractual edition should be established at project initiation together with owner specifications and applicable jurisdictional requirements.
The governing code or standard does not replace project-specific Engineering. Existing tank condition, service, geometry, loads, materials, and repair scope determine which requirements must be transferred to each component and what objective evidence will be required before release.
Cost control from the fabrication stage
The cost of a component does not end with its purchase price. Rework, expedited freight, reinspection, field modifications, unproductive labor hours, and turnaround extensions can significantly increase total supply cost when a deviation reaches the installation stage.
During a turnaround, this effect becomes more significant. A late delivery, an incomplete component, or a fabricated item requiring field modification can delay downstream activities and extend the period during which the tank remains out of service. For this reason, lead time, component conformity, and delivery reliability are part of the technical and economic performance of the supply process.
Cost control begins in Engineering. An interference identified before cutting may require only a drawing or dimensional revision; the same condition discovered during field installation may require disassembly, refabrication, additional NDE, resource mobilization, and rescheduling of the work front. Integrating Engineering, Fabrication, and Inspection shifts these decisions toward stages where corrections are less disruptive.
At HMT, integrated control does not require every material or process to be produced internally. When specific supplies or processes come from specialized suppliers, the objective is to maintain technical control over specifications, interfaces, traceability, inspection, and acceptance criteria. This approach allows fabrication and supply decisions to balance capacity, lead time, and cost while maintaining conformity with project requirements. HMT’s published turnaround services specifically include Supplier Surveillance and Inspection and verification of compliance with client requirements.
Conclusions
Controlling the fabrication and supply of tank components means maintaining verifiable continuity among Engineering, materials, production, Inspection, and field execution. At HMT, this capability is supported by company fabrication facilities, In-House Engineering Services, certified welders, Level II inspectors, CWI capabilities, In-House NDE Capabilities, Mechanical Testing and Metallurgical Testing services, and experienced installation and Tank Repair & Maintenance teams.
The objective goes beyond fabricating a component that conforms to a drawing. We aim to deliver consistent, documented assemblies prepared to integrate into the planned installation sequence, reducing the variability that can turn a fabrication detail into rework, additional cost, or an extended turnaround.
Are you planning a turnaround, tank repair, or upgrade? HMT integrates Engineering, Fabrication, Inspection, and installation support to supply tank components aligned with project technical requirements and schedule.
Sources
- HMT – Fabrication Services
- HMT – ALLENTECH Skin and Pontoon IFR
- HMT – ALLENTECH Full Contact IFR
- HMT – Turnaround Inspection Services
- HMT – Tank Repair & Maintenance
- HMT – Mechanical Testing
- American Petroleum Institute – API Standard 650, 14th Edition Update