The global knowledge network for professionals in the energy and industry

The ground system that saves aircraft: The engineering behind EMAS

The EMAS system dissipates kinetic energy through controlled deformation to stop aircraft that overshoot the runway.
EMAS aircraft system

A 180-ton aircraft traveling at over 250 km/h contains an amount of energy comparable to that of thousands of moving vehicles. Upon landing, and when the runway ends, engineering has seconds to respond and prevent a catastrophe.

Perhaps few people are aware that modern airport engineering faces two different, yet closely related problems: providing a surface capable of supporting the high loads transmitted by aircraft and, at the same time, reducing the consequences of an event in which an aircraft leaves the runway.

The first corresponds fundamentally to pavement design. The second belongs to the scope of runway safety and systems intended to mitigate the consequences of a runway excursion, a term used to describe an aircraft that accidentally leaves the runway surface, whether by overrunning its end (overrun) or by deviating laterally (veer-off).

It is important to know this difference because it allows an understanding of the logic of Engineered Materials Arresting Systems (EMAS): while pavement must support and distribute loads, an EMAS system is designed to absorb kinetic energy through controlled deformation.

Let us take as an example the accident that occurred on September 6, 2026, at Miami International Airport, in which a Boeing 767-33A cargo aircraft operated by 21 Air overran the end of runway 30. This recent runway excursion event allows us to contextualize the importance of these technologies and analyze the associated challenges, although the National Transportation Safety Board (NTSB) investigation remains open and available data are preliminary. (NTSB 2026, September 9)

Rigid pavement on airport runways

Runways intended for heavy aircraft operations require paving systems capable of resisting repetitive loads, flexural stresses, thermal variations, and severe environmental conditions.

In a rigid pavement, the concrete slab transmits and distributes loads over the supporting structure. Its behavior depends first on the strength of the concrete, and second on the thickness of the slab, the characteristics of the subbase and subgrade, joints, load transfer system, and drainage conditions.

Among its main elements are:

  • Structural strength of concrete: The slab must provide sufficient capacity against flexural stresses and loads transmitted by the landing gear.
  • Reinforcement and crack control: Depending on the system used, steel can be used to control cracking and contribute to the structural behavior of the slab.
  • Dowels: In transverse joints, these elements allow load transfer between adjacent slabs and help limit level differences between them.
  • Surface texture: Grooving and other texture characteristics favor surface drainage and contribute to maintaining adequate friction conditions between tire and pavement, particularly in the rain.
1 IMG 1 ING The ground system that saves aircraft The engineering behind EMAS resultado

When a runway excursion occurs

There is, however, a fundamental limit to this approach. The runway is designed for the aircraft to operate on the pavement. When an aircraft leaves the paved surface, the problem changes. The question is no longer solely the structural capacity of the concrete. The dominant parameter becomes the kinetic energy that must be dissipated.

In a simplified manner:

Ek​=21​mv2

Where m represents the mass of the aircraft and v its velocity.

In simpler words, physics shows us that kinetic energy increases proportionally to the square of velocity. When a heavy aircraft moves along the runway at critical speeds of between 240 and 300 km/h and suffers a runway excursion (goes beyond the paved boundary), the energy it carries with it is destructive. To counteract this danger, the EMAS system acts as an absorption barrier: its deformable structure slows down the airplane by dissipating that immense kinetic energy before a major accident occurs.

Here a conceptual difference emerges: Pavement manages loads; an arresting system manages energy.

RSA, RESA and EMAS: Three concepts that should not be confused

One of the aspects worth clarifying in airport safety analysis is the difference between Runway Safety Area (RSA), Runway End Safety Area (RESA), and Engineered Materials Arresting System (EMAS).

1 IMG 2 ING The ground system that saves aircraft The engineering behind EMAS resultado 1

In the U.S. regulatory system, the RSA is the safety area associated with the runway and constitutes one of the main mitigation measures against excursions. The FAA describes it as a cleared, leveled, and prepared area to provide additional space for an aircraft to decelerate after leaving the runway surface. (FAA, 2025)

RESA, on the other hand, is a concept used in international aerodrome standards and practice, particularly within the framework of ICAO. For runways of certain reference codes, ICAO establishes minimum dimensions and recommends larger dimensions when airport conditions permit. When physical constraints prevent achieving certain recommended dimensions, alternative mitigation measures can be studied.

EMAS is different. It does not simply constitute a certain length of ground, nor should it be described as a direct replacement for a RESA. It is an arresting system designed to manage the energy of an aircraft that leaves the runway, especially at airports where it is difficult to provide a full-dimension conventional RSA. (FAA, 2026, August 12) That is to say, if someone asks, what is EMAS for? Let’s put it graphically: If an airplane comes in landing very fast (or aborts takeoff at the last minute) and runs out of runway, instead of running off onto the grass, crashing into a highway, or crashing, the tires enter the EMAS. It is like the runaway truck ramps or expanded clay beds on a highway where heavy vehicles, when experiencing a brake failure, have this system as a braking option.

This distinction is fundamental to properly understanding its function.

The engineering of controlled deformation

The operating principle of EMAS is relatively simple to explain, although its design is considerably more complex. The system uses engineered materials capable of deforming in a predictable manner when the aircraft’s wheels penetrate the arrestor bed. The deformation generates forces resisting movement. Part of the kinetic energy of the aircraft is transformed into deformation work, and as a result, the speed decreases.

The FAA explains that the EMAS material crushes or collapses under the weight of the aircraft, producing considerable deceleration in a relatively short distance. A standard EMAS is designed to stop the critical aircraft when entering the system at a speed of up to 130 km/h (70 knots), although the specific capacity depends on the design of each installation.

In systems based on cellular concrete blocks, the material possesses a low-density structure designed to collapse under a given load. The geometry, density, strength, and system configuration must be selected according to the characteristics of the aircraft operating at the airport.

The FAA currently identifies EMAS systems based on cellular concrete material blocks and also systems based on foamed silica. In both cases, these are materials specifically developed to fulfill an arresting function and not merely a simple low-strength pavement.

Speed, mass and arresting capacity

The capacity of an EMAS cannot be expressed solely by a fixed length.

The design depends on variables such as:

  • Aircraft mass and configuration.
  • Entry speed.
  • Geometry and available length.
  • Mechanical characteristics of the material.
  • Landing gear configuration.
  • Site conditions.
  • Environmental conditions.
  • Maintenance requirements.

The FAA notes that the bed length and its separation from the end of the runway depend on the airport configuration and the fleet using the runway. Therefore, design values should not be extrapolated from one installation to another without performing the corresponding engineering analysis. (FAA, 2026, August 12)

This distinction also helps avoid a common simplification: presenting 130 km/h or 70 knots as a universal operating speed for any EMAS. In reality, it is a criterion associated with the standard design described by the FAA and not an inherent property independent of the installation.

From structural strength to energy management

The evolution from rigid pavement to systems like EMAS represents something deeper than replacing one material with another. It represents a shift in how airport safety is conceived. For decades, airport engineering focused primarily on ensuring that the aircraft could operate within the expected limits of the runway. The development of safety areas and subsequently arresting systems expanded that concept to also consider scenarios in which the aircraft leaves the operational surface.

During the 1990s, the FAA began research aimed at improving safety at airports where obtaining a full RSA was not possible. That work involved, among other participants, the University of Dayton, the Port Authority of New York and New Jersey, and Engineered Arresting Systems Corporation, later acquired by the current manufacturer of these systems.

The result was a technology in which the material is no longer simply a load-bearing element, but comes to perform a dynamic function: deforming in a controlled manner to dissipate energy.

Conclusions

Pavement engineering is oriented toward supporting the aircraft’s movement; EMAS engineering is oriented toward managing its consequences when that movement leaves the RSA and RESA zone.

The value of EMAS does not lie in presenting it as a universal solution; it is understanding it as a controlled energy management system that has been designed for specific aircraft, speeds, airport configurations, and site conditions. That is the most important conceptual evolution: moving from thinking solely about infrastructure resistance to also designing mechanisms capable of controlling energy when operation deviates from the planned scenario.

References

  1. Federal Aviation Administration. (2012). AC 150/5220-22B: Engineered Materials Arresting Systems (EMAS) for aircraft overruns. U.S. Department of Transportation, Federal Aviation Administration.
  2. Federal Aviation Administration. (2025). Runway safety areas (RSAs). U.S. Department of Transportation, Federal Aviation Administration.
  3. Federal Aviation Administration. (2026, August 12). Engineered Material Arresting System (EMAS). U.S. Department of Transportation, Federal Aviation Administration.
  4. International Civil Aviation Organization. (2009). Runway safety manual (1st ed.). ICAO.
  5. FAA, Engineered Materials Arresting Systems (EMAS)
  6. FAA, AC 150/5220-22B, EMAS for Aircraft Overruns
  7. NTSB, Runway Overrun of 21 Air Flight 7598, DCA26MA352

Written by
Verified Author

TSU in General Mechanics. With more than 35 years of experience in Mechanical Integrity and Asset Reliability, Quality Control and Inspection of equipment for the oil industry.